GlasGrid® CG100
Designed for use in spot repairs on roadways, such as reinforcing concrete joints, major intermittent transverse cracks, construction joints on widenings, and joints on trench repairs.
Product Specifications:
Specification For Use in Asphalt Overlays
|
CG-100
|
Imperial*
|
Metric**
|
Tensile Strength
Based On Component Strand Strength
Test Method ASTM D 6637 |
Across Width
560 lbs/in.
Across Length
560 lbs/in. |
Across Width
100 kN/m.
Across Length
100 kN/m. |
Elongation at Break
Test method ASTM D 6637 |
Less than 3% |
Less than 3% |
Melting Point
Test Method ASTM D 276 |
Greater than 425°F |
Greater than 218°C |
Mass/Unit Area
Test Method D5261-92 |
14 oz/yd2 |
475 g/m2 |
| Asphalt Retention |
0.2 gal/yd2 |
0.9 l/m2 |
| Roll Length† |
197 ft. |
60 m |
| Roll Width† |
5 ft. |
1.5 m |
| Roll Area† |
109 yd2 |
90 m2 |
| Grid Size |
1 in x 1 in |
25 mm x 25 mm |
| Material |
Fiberglass reinforcement with modified polymer coating and pressure sensitive adhesive backing bonded to a non-woven polypropylene specifically engineered for asphalt overlays. |
* All imperial values are approximate.
** All metric values are nominal.
† Product is sold by the Roll.
Technical Specifications:
C50/C100 Specs
Installation Procedures:
The following are general guidelines to ensure a successful installation of CG System. For each specific project, a construction engineer will provide exact specifications for installation.
Surface Preparations
- As directed by an engineer, repair potholes, cracks greater than 6mm (1/4"), badly damaged or rough pavement that may require milling and the placement of a leveling course.
- Pavement must be free of dirt, water, oil and other foreign materials. Broom or air clean the surface so it is clean and dust-free.
- Apply tack coat uniformly over the prepared asphaltic concrete surface at a residual rate of 0.9 - 1.36 litres/m2 (0.2 - 0.3 gal/yd2) using a calibrated distributor truck, ensuring that the application rate remains constant. The tack shall contain a minimum of 70% solids.
- The tack coat area must be a minimum of 75 mm (3'') wider than the CG System.
Road Surface Condition
- The road must be dry. Do not install CG System during any precipitation.
- The road surface temperature must be between 5°C* (40°F**) and 60°C* (140°F**). On asphalt surfaces less than 24 hours old, the surface temperature should be between 5°C* and 46°C* (40°F** and 110°F**).
CG Placement Method
- Place the CG System while the tack coat is still tacky/broken. Use a mechanical placement tractor or place manually.
- Keep the material flat and wrinkle free. Installation may require hand brooming. For sharp curves, cut edges and fold over in the direction of the placement of asphalt overlay.
- Overlaps must be a minimum 25mm (1'') to ensure a continuous moisture barrier.
Paving Method
- Pave with hot mix overlay.
- Asphalt overlay must be a minimum of 50mm (2'') compacted thickness.
- All of the CG System must be paved over on the day of placement.
Other Important Considerations for Best Results
- Because glass is a skin irritant, we recommend that workers shall wear gloves
- To cut CG System to desired length, lay it over ironworks, roll, and then cut using a sharp utility knife.
- CG System must be applied so that the material lies flat on the road surface with no ripples. Providing sufficient tension during application will eliminate ripples.
- Overlap all end roll joints 75-150 mm (3"-6"). Ensure that the overlaps are shingled in the direction of paving and that these overlaps also receive an application of tack.
- Overlap side joints 25-50 mm (1"-2").
- To maximize product performance, only construction and emergency vehicles shall be allowed to drive on the CG System.
- The above directions are a brief guide to installation. For complete directions, consult with your distributor.
*All Metric values are nominal.
**All imperial values are approximate.
|
